17 Dec
2006
17 Dec
'06
11:42 p.m.
Hello,
I had a connection problem with router (Zyxel prestige 650H) after to be connected under
windows, for an unknown reason configuration parameters were modified and then I have to
reinitialize the hardware and reconfigurate it (with ancien parameters such as key for
wep, etc) but after, while connection works normally under windows, this works not at all
under linux!!I have a laptop which run under mandriva2007, wireless liaison is assumed
with ndiswrapper and list of interfaces gives:
ifconfig -a
eth0 Link encap:Ethernet HWaddr 00:C0:9F:B7:BC:13
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interruption:233
eth1 Link encap:Ethernet HWaddr 00:14:A4:3C:E2:52
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interruption:169 Mémoire:c0304000-c0306000
lo Link encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
adr inet6: ::1/128 Scope:Hôte
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:66 errors:0 dropped:0 overruns:0 frame:0
TX packets:66 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
RX bytes:5116 (4.9 KiB) TX bytes:5116 (4.9 KiB)
sit0 Link encap:IPv6-dans-IPv4
NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
network card is Broadcom BCM4318 AirForceOne 54g, but when I doing ifup eth1 (interface
used for wireless access) I have as answer: "no link found; check cable?"; I
have similar problem with another laptop running under suse10: no mean to obtain an normal
IP adress and then any link for the access.
Any suggestion?
Thank you in advance
Cheers
M.
18 Dec
18 Dec
7:44 a.m.
Quoting Michel Maria-Sube <mgms1(a)yahoo.com>:
Hello,
I had a connection problem with router (Zyxel prestige 650H) after to
be connected under windows, for an unknown reason configuration
parameters were modified and then I have to reinitialize the hardware
and reconfigurate it (with ancien parameters such as key for wep,
etc) but after, while connection works normally under windows, this
works not at all under linux!!I have a laptop which run under
mandriva2007, wireless liaison is assumed with ndiswrapper and list
of interfaces gives:
Try a ifdown before you do ifup. This might resetting the card. I have
experienced that sometimes cards become an unstable state and behave
strangely.
HTH
Alex
----------------------------------------------------------------
This message was sent using IMP, the Internet Messaging Program.
11:58 a.m.
unfortunately it doesn't work; under suse 10 here is the sequence
gms:/home/mgms/programs/scjda-sp9316524 # iwconfig
lo no wireless extensions.
sit0 no wireless extensions.
eth1 no wireless extensions.
eth0 IEEE 802.11b ESSID:"Wireless" Nickname:"ipw2100"
Mode:Managed Frequency:2.437 GHz Access Point: 00:A0:C5:66:7D:B6
Bit Rate=11 Mb/s Tx-Power:off
Retry min limit:7 RTS thr:off Fragment thr:off
Encryption key:3030-3030-3030-3030-3030-3030-3030-3030 Security mode:open
Power Management:off
Link Quality=100/100 Signal level=-37 dBm
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:12 Missed beacon:0
so eth0 is the interface for wireless connection
mgms:/home/mgms/programs/scjda-sp9316524 # ifdown eth0
eth0 device: Intel Corporation PRO/Wireless LAN 2100 3B Mini PCI Adapter (rev 04)
eth0 configuration: wlan-id-00:04:23:77:53:2b
mgms:/home/mgms/programs/scjda-sp9316524 # ifup eth0
eth0 device: Intel Corporation PRO/Wireless LAN 2100 3B Mini PCI Adapter (rev 04)
eth0 configuration: wlan-id-00:04:23:77:53:2b
eth0 starting wpa_supplicant
Starting DHCP Client Daemon on eth0... . . . . . no IP address yet... backgrounding.
and after:
mgms:/home/mgms/programs/scjda-sp9316524 # iwconfig eth0 rate 11
mgms:/home/mgms/programs/scjda-sp9316524 # iwconfig eth0 essid Wireless
mgms:/home/mgms/programs/scjda-sp9316524 # iwconfig eth0 key open
mgms:/home/mgms/programs/scjda-sp9316524 # iwconfig eth0 enc <the key>
mgms:/home/mgms/programs/scjda-sp9316524 # dhcpcd eth0
...very long the give hand
and after:
mgms:/home/mgms/programs/scjda-sp9316524 # ifconfig -a
eth0 Lien encap:Ethernet HWaddr 00:04:23:77:53:2B
BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:14 dropped:0 overruns:0 frame:0
TX packets:1 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
RX bytes:0 (0.0 b) TX bytes:84 (84.0 b)
Interruption:10 Adresse de base:0x6000 Mémoire:e0206000-e0206fff
eth1 Lien encap:Ethernet HWaddr 00:C0:9F:2E:D9:BF
inet adr:198.168.10.1 Bcast:198.168.10.255 Masque:255.255.255.0
adr inet6: fe80::2c0:9fff:fe2e:d9bf/64 Scope:Lien
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
Interruption:10
lo Lien encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
adr inet6: ::1/128 Scope:Hôte
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:206 errors:0 dropped:0 overruns:0 frame:0
TX packets:206 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
RX bytes:14124 (13.7 Kb) TX bytes:14124 (13.7 Kb)
sit0 Lien encap:IPv6-dans-IPv4
NOARP MTU:1480 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
and no access is provided
under mandriva2007 I've completely loss the interface for wireless access and
I'm unable to reconfigurate it with ndiswrapper
nevertheless it works correctly under windows!! (but what a punishment)
suggestions welcome
cheers
M.
Alex.Loes(a)lll.lu wrote:
Quoting Michel Maria-Sube :
Hello,
I had a connection problem with router (Zyxel prestige 650H) after to
be connected under windows, for an unknown reason configuration
parameters were modified and then I have to reinitialize the hardware
and reconfigurate it (with ancien parameters such as key for wep,
etc) but after, while connection works normally under windows, this
works not at all under linux!!I have a laptop which run under
mandriva2007, wireless liaison is assumed with ndiswrapper and list
of interfaces gives:
Try a ifdown before you do ifup. This might resetting the card. I have
experienced that sometimes cards become an unstable state and behave
strangely.
HTH
Alex
----------------------------------------------------------------
This message was sent using IMP, the Internet Messaging Program.
_______________________________________________
Lilux-help mailing list
Lilux-help(a)lilux.lu
http://lilux.lu/mailman/listinfo/lilux-help
12:40 p.m.
Quoting Michel Maria-Sube <mgms1(a)yahoo.com>:
I found
http://www.linuxquestions.org/hcl/showproduct.php?product=3587&cat=all
on the net. It seems that the card is turned off and somehow Linux
isn't able to turn it on.
I experienced also problems with a card with a native Linux driver. I
think that Wireless is a little bit tricky.
Nevertheless, I have no problems with a D-Link pci card.
Al
----------------------------------------------------------------
This message was sent using IMP, the Internet Messaging Program.
6541
days inactive
6542
days old
3 comments
2 participants
participants (2)
-
Alex.Loes＠lll.lu -
Michel Maria-Sube