Hello,
I've recently installed Kubuntu10.10 on a laptop Acer TM660 (rather
old hardware now), running in 32b
with a Centrino chip for wireless connection but I didn't find how to
configure interfaces; in the
menu to configure the network I was able to put parameters for new
wireless connection but
surprisingly there is no option to bind connection with a specific
interface; thus, after that,
there is no mean to set up interface as it is not yet configurated;
command ifconfig -a gives:
eth0 Link encap:Ethernet HWaddr 00:c0:9f:2e:d9:bf
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Packets reçus:0 erreurs:0 :0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
Octets reçus:0 (0.0 B) Octets transmis:0 (0.0 B)
Interruption:10
eth1 Link encap:Ethernet HWaddr 00:04:23:77:53:2b
UP BROADCAST MULTICAST MTU:1500 Metric:1
Packets reçus:0 erreurs:0 :0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
Octets reçus:0 (0.0 B) Octets transmis:0 (0.0 B)
Interruption:10 Adresse de base:0xa000 Mémoire:e0206000-e0206fff
lo Link encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
adr inet6: ::1/128 Scope:Hôte
UP LOOPBACK RUNNING MTU:16436 Metric:1
Packets reçus:116 erreurs:0 :0 overruns:0 frame:0
TX packets:116 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
Octets reçus:8784 (8.7 KB) Octets transmis:8784 (8.7 KB)
and content of file /etc/network/interfaces is only:
auto lo
iface lo inet loopback
Problem is not solved if i do following instructions:
iwconfig eth1 essid <my network name>
iwconfig eth1mode Managed
iwconfig eth1 rate auto
iwconfig eth1 key <myKey>
Any suggestion(s)?? Thanks in advance
Regards
Hello,
I've recently installed Kubuntu10.10 on a laptop Acer TM660 (rather
old hardware now), running in 32b
with a Centrino chip for wireless connection but I didn't find how to
configure interfaces; in the
menu to configure the network I was able to put parameters for new
wireless connection but
surprisingly there is no option to bind connection with a specific
interface; thus, after that,
there is no mean to set up interface as it is not yet configurated;
command ifconfig -a gives:
eth0 Link encap:Ethernet HWaddr 00:c0:9f:2e:d9:bf
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
Packets reçus:0 erreurs:0 :0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
Octets reçus:0 (0.0 B) Octets transmis:0 (0.0 B)
Interruption:10
eth1 Link encap:Ethernet HWaddr 00:04:23:77:53:2b
UP BROADCAST MULTICAST MTU:1500 Metric:1
Packets reçus:0 erreurs:0 :0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:1000
Octets reçus:0 (0.0 B) Octets transmis:0 (0.0 B)
Interruption:10 Adresse de base:0xa000 Mémoire:e0206000-e0206fff
lo Link encap:Boucle locale
inet adr:127.0.0.1 Masque:255.0.0.0
adr inet6: ::1/128 Scope:Hôte
UP LOOPBACK RUNNING MTU:16436 Metric:1
Packets reçus:116 erreurs:0 :0 overruns:0 frame:0
TX packets:116 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 lg file transmission:0
Octets reçus:8784 (8.7 KB) Octets transmis:8784 (8.7 KB)
and content of file /etc/network/interfaces is only:
auto lo
iface lo inet loopback
Problem is not solved if i do following instructions:
iwconfig eth1 essid <my network name>
iwconfig eth1mode Managed
iwconfig eth1 rate auto
iwconfig eth1 key <myKey>
Any suggestion(s)?? Thanks in advance
Regards
Dear all,
While updating the error with following message appears:
Message did not receive a reply (timeout by message bus)
I already tried to solve the problem by looking for a troubleshooting.
Does anybody know what to do?
Thank you
--
Jean-Paul Piazzolla
YES academy
www.yesacademy.lu
